High Speed Electric Winch

High speed electric winch is the basic lifting and pulling device that used in construction site. According to the power system, our high speed winch can be divided into different types: high speed electric winch, high speed hydraulic winch. Manual winch in our group mainly is capstan that used in ship and deck. High speed electric winch of our manufacturer has many series, and each one has its advantage and suitable occasions. There is a brief introduction that helps you having a better understanding of our winch machine. Under the help of the guidance, you will find the winch that suits your actual working requirements well.

Different types of high speed electric winch

AQ-JK high/fast speed electric winch is mainly used for the construction of the material increases, traction weight and as the main lifting crane, derrick, gantry hoisting trolley and special promotion hoist. It is suitable for construction, construction and installation of small equipment in construction and mining area. Rated tension or load: 0.5t-10t; Volume of reel: 50m-500m; Speed: 20-30 m/min.

AQ-JKL fast speed electric piling winch is mainly used for vertical lifting of construction sites, factories and mines, ports, etc., especially suitable for the free falling and piling operation of Bridges, wharf and building foundations. The structural features of the main shaft rotation (commonly known as rotating shaft). Rated tension or load: 2t-10t; Volume of reel: 50m-250m; Speed: 28-36m/min.

AQ-JKD series fast speed winch is a new type of hoist with planetary transmission. It has the advantages of compact structure, smooth operation, easy operation, simple maintenance, low noise and long service life. Widely used in building construction, docks, lifting and installation of Bridges, metallurgical and other industries, in line with national GB/T10055-1996 construction lifter safety rules and the state industry standard JGJ88-92 hoist safety technical specification requirements. Rated tension or load: 0.75t-2t; Volume of reel: 100m-190m; Speed: 20-50m/min.

AQ-JMM friction type electric winch is mainly used for the long distance traction of various large and special concrete, steel structure, steel cable and cable, etc. Its characteristic steel wire rope speed is constant, lifting is stable. It is applicable to all kinds of Bridges, ports, wharves and other road and bridge engineering construction and large scale factory and power engineering equipment installation. Rated tension or load: 10t-55t; Volume of reel: 1000m-5000m; Speed: 5-11m/min.

Perfect after-sale service provided by us

1.Our professional engineers are ready to go abroad for installation, commissioning, instruction and maintenance whenever necessary;

2.We offer free training and guidance of operation and maintenance in our factories as clients need;

3.We also have free training and guidance for the clients’ service and maintenance staff about installing, debugging, operating or maintaining the high speed electric winch;

4.We provide the perfect service to make sure that the winch machine you purchase from us work effectively and reliably all the time during its service life.

Main part of high speed electric winch

The motor is an important part of the high speed electric winch and also the most expensive part in the winch. If damaged, the repair or replacement cost will be very high. So here we remind customers to take care of the winch or winch motor. The maintenance method is as follows:

1. The environment should be kept dry frequently, and the surface of the motor should be kept clean. The inlet should not be blocked by dust or fiber.

2. When the motor’s thermal protection occurs continuously, it should be found out that the fault comes from the motor or the overload or protection device setting value is too low, and after the fault is eliminated, the operation can be put into operation.

3. The motor should be well lubricated during operation. The general electric motor runs about 5000 hours, namely should replenish or replace the grease, when the bearing is overheated or lubricated, the hydraulic pressure changes the grease in time. Replacing grease, should clean up the old oil, and gasoline wash oil bearing and the bearing cover, then put the ZL – 3 lithium base grease filling bearing between the inner and outer ring cavity 1/2 (2) and two-thirds (4, 6, 8).

4. When the life of the bearing is finished, the vibration and noise of the motor will increase significantly. When the radial clearance of the bearing reaches the following value, the bearing shall be replaced.

5. When the motor is removed, the rotor can be removed from either the shaft or the non-extension end.

6. If it is not necessary to remove the fan, it is more convenient to remove the rotor from the non-shaft end. When the rotor is drawn out of the stat-or, it should be prevented from damaging the stat-or winding or insulation.

7. Replacing winding must take note of the original winding form, size and number of turns, wire gauge, etc., when the data lost, should be to the factory, change the original design winding, often worsen or a few of the motor performance, even not be able to use.

Manufactures of high speed electric winch

Our company is configured with the advanced equipment in this industry. It also has the bigger test rig, testing center and form a complete set of equipment, such as CNC plane drilling machine, CNC flame plasma cutting machine, full-function CNC lathe, digital display boring machine, NDT instruments, etc. Advanced equipment lays a solid foundation for making high-quality products.

The quality assurance system of the company emphasizes process control, and the concept of quality control permeates the whole process of product design, manufacturing and inspection. Advanced detection equipment, meticulous inspection process, strict control assessment procedures, make every product be guaranteed. Our company has been committed to creating high-end products and providing customers with perfect solutions. Therefore, don’t hesitate to contact us for your satisfactory winch.